Natural Look
Clear Sealer

Natural Look is a high performance, ready-to-use, solvent free reactive silane modified waterborne siloxane clear penetrating sealer. Natural Look clear sealer penetrates the surface and chemically bonds directly with the substrate which results in a surface that is highly resistant to both moisture and salt. Natural Look clear sealer is designed to provide long lasting water repellency from water–induced damages without altering the natural appearance of the substrate.

Features & Benefits

  • Imparts water repellency
  • Preserves the natural appearance of substrate
  • Protects against damage caused by freeze-thaw cycles
  • Dries clear, non-yellowing, non–film forming
  • Penetrating and vapor permeable
  • Eco-Friendly and low VOC

Directions

Always test each type of surface to ensure desired results. Let test area dry before inspection. Stir or shake before applying. For best results, follow this procedure:

  1. Do not apply sealer when temperatures are less than 50°. For expected to drop below 50°F during the next 6 hours.
  2. Do not apply sealer when temperatures are higher than 90°F.
  3. Do not apply sealer in rainy conditions or when rain is expected within 24 hours.
  4. Application to be made using low pressure high quality pump sprayer, brush or 3/8” nap roller. DO NOT ATOMIZE.
  5. Holding tip 6” – 12” from surface using overlapping spray pattern and fanning motion at the end of each horizontal pass.
  6. Entire area being treated is to be saturated but do not allow sealer to puddle. If puddling occurs make sure to disperse puddle area with a broom or paint roller in order to avoid any whiting effect which may occur.
  7. Clean all dips, runs, and overspray residue while still wet.
  8. Allow product to dry for 24 hours.

MIXING: Always mix thoroughly before and during application.

THINNING: This product is not to be thinned.

CLEANUP: Clean all equipment immediately after use with warm soapy water. Completely flush all spray equipment with this solution.

DRYING TIME@ 77OF @ 50% RH: Temperature and humidity dependent. To touch: 1 hour To recoat: 4 hours

Specifications

  • Available Sizes:
    • 1 Gallon (~4 liters)
    • 5 Gallon (~19 liters)
  • SOLIDS: 25.00 ± 1% by weight 23.00 ± 1% by volume
  • V.O.C LEVEL: 0 g/L
  • WEIGHT / GALLON: 8.5± 0.5 lbs.
  • pH: 8.5 – 9.5
  • FINISH: N/A – Penetrating
  • FLASH POINT: Non-flammable
  • FIRE RATING: Class A
  • VISCOSITY: Liquid
  • SUGGESTED FILM THICKNESS, COVERAGE PER COAT:
    150 – 300 sq.ft. per gal. (First Coat)
    300 – 400 sq.ft. per gal. (Second Coat)
    *Coverage figures do not include surface porosity, irregularities & material loss due to application methods.

Safety

  • Handling: Wear suitable gloves and eye protection. Ensure adequate ventilation during application.
  • Storage: Store in a cool, dry place away from direct sunlight and frost. Keep the container tightly closed.
  • Flammability: Natural Sealer is non-flammable, the product can emit toxic fumes when exposed to flame. Keep away from extreme heat and open flames.
  • First Aid:
    • Eye Contact: Rinse immediately with plenty of water and seek medical advice.
    • Skin Contact:  Wash with soap and water.  
    • Ingestion:  Do NOT induce vomiting. Seek medical attention immediately.
    • Inhalation: Remove to fresh air. If breathing is difficult, seek medical attention. Use artificial respiration if necessary.
Instagram Facebook Youtube Linkedin Book-open
cropped-cropped-Kong-Logo-1.webp

Hours of Operation

Monday – Friday
7:00am – 5:00pm

 

Saturday
8:00am – 12:00pm